~~ Hydro Systems Whirlpool Baths ~~

HS 6032 BF Roll-In Shower

Features

Overall Dimensions Installed:
60"W x 32"D x 74" H
Note: the bottom of the shower must be 2" below the finished floor for the treshold to be level with the finished floor
Gel Coat Finish
Flame spread rating of 200 or less
Smoke density rating of 450 or less per ASTM E84
Galvanized steel reinforced stiffeners
Extra reinforcing in all critical areas
Slip resistant floor
21" x 42" Satin finish stainless steel grab bar vertically mounted, 1½" diameter
Choice of Naugahyde over foam rubber or a hard phenolic folding wheelchair transfer seat factory installed
60" Satin finish stainless steel curtain rod, installed
Drain is chrome-plated brass and included with shower strainer
Strainer has ¼" minimum grate openings and is flush with the floor surface
Unit is packaged in cardboard box on forklift pallet
Full LTL wooden shipping crate available as an option

Download This Page as PDF Document

ADA & Title 24 compliant when equipped as shown and properly installed*

Left hand shower shown.
* Shower must be recessed 2" to meet ADA requirements

Galvanized steel and/or wood reinforcement
will vary due to application of accessories

G* = from side wall H* = from back wall
Model	A width	B depth	C width	D depth	E finish	F overall	G*	H*	I	J	K	L	M	N	O	P	Q
HS 6032 BF	60"	32"	62"	34"	77"	78"	31"	16½"	60"	2"	1"	seat	18"	n/a	60"	n/a	21"x42"
	R	S	T	U	V	W	X	Y	Z
	34½"	n/a	n/a	n/a	n/a	wet wall	n/a	n/a	n/a

Standard Code Listings and Approvals	Warranty
IAPMO/UPC - Uniform Plumbing Code - File 3307 ANSI-Z124.2 - Standard for Plastic Shower Units ASTM F-446 - Grab Bars & Accessories ASTM F-462 - Slip Resistance	Hydro Systems producers are backed by our exclusive 5 year limited warranty. (See warranty for complete details)
Suggested Mechanical Specifications
Hydro Systems HS 6032 BF shower with 5 year limited warranty, 60" Wide x 32" Deep x 77" High with folding wheelchair transfer seat conforming to ADA accessibility standards, 1" O.D. satin finish stainless steel curtain rod, 21" x 42"satin finish stainless steel grab bar on rear wall, 24" satin finish stainless steel grab bar, center rear drain with sloping integrally molded slip-resistant floor. Units shall be molded of gel-coated fiberglass reinforced polyester resin. Units shall meet or exceed physical and performance requirement for Type 2 gel-coated fixtures [of ANSI Z124.2 showers]. Standing/walking surfaces shall meet slip-resistance requirements of Consumer Safety Specification ASTM F-462, with static friction coefficient no less than 0.04.	Handicapped grab bars shall be nom. 1½" O.D. and support a minimum load of 250lbs. in accordance with the Consumer Safety Specification ASTM F-446 and ANSI A117.1 guidelines. Units shall have a flame spread rating of 200 or less and a smoke density rating of 450 or less per ASTM E84. Units shall bear or have a fixed to them a molded manufacturer's logo and/or permanent label showing manufacturer's name and model number and the seal of the Uniform Plumbing Code and shall be accompanied by detailed installation recommendations. Also affixed and for removal by the owner/occupant/user only, unit shall be equipped with user maintenance instructions and the full text of the limited warranty. As manufactured by Hydro Systems Inc. - Valencia, California.
All specifications subject to change without notice.

~~ Hydro Systems Whirlpool Baths ~~

NEW!