~~ Hydro Systems Whirlpool Baths ~~

 

 
HS 6030 BF Roll-In Shower
 

Features

Overall Dimensions Installed:
60"W x 30"D x 77" H
Gel Coat Finish
Note: the bottom of the shower must be 2" below the finished floor for threshold to be level with the finished floor
Flame spread rating of 200 or less
Smoke density rating of 450 or less per ASTM E84
Soap dish (optional)
Galvanized steel reinforced stiffeners
Extra reinforcing in all critical areas
Slip resistant floor
21" x 42" Satin finish stainless steel grab bar
Choice of Naugahyde over foam rubber or a hard phenolic folding wheelchair transfer seat factory installed
60" Satin finish stainless steel curtain rod, installed
Drain is chrome plated brass and included with shower
Strainer has ¼" minimum grate openings and is flush with the floor surface
Unit is packaged in cardboard box on forklift pallet
Full LTL wooden shipping crate available as an option

ADA & Title 24 compliant when equipped as shown and properly installed*

 


Right hand shower shown.
* Shower must be recessed 2" to meet ADA  & Titel 24 requirements



Galvanized steel and/or wood reinforcement
will vary due to application of accessories

 
Model A
width 		B
depth		 C
width		 D
depth		 E
finish		 F
overall		 G* H* I J K L M N O P Q
HS 6030 BF 60" 30"  62" 32" 77" 78" 31" 16" 60" 2" 1" seat 18" n/a 60" n/a 21"x 42"

  R

 S  T

U  

  V W X Y   Z
34½" n/a

  n/a

  n/a n/a wet wall n/a n/a

n/a
G* = from side wall   H* = from back wall

Standard Code Listings and Approvals

Warranty
ANSI-Z124.2 - Standard for Plastic Shower Units
ASTM F-446 -  Grab Bars & Accessories
ASTM F-462 -  Slip Resistance
ANSI A117.1 - Accessibility & Usability

Hydro Systems producers are backed by our exclusive 5 year limited warranty.
(See warranty for complete details)

Suggested Mechanical Specifications

Hydro Systems HS 6030 BF shower with 5 year limited warranty, 60" Wide x 30" Deep x 77" High with folding wheelchair transfer seat conforming o ADA & Title 24 accessibility standards, 1" O.D. satin finish stainless steel curtain rod, 21" x 42" satin finish stainless steel grab bar, center drain with sloping integrally molded slip-resistant floor.
 
Units shall be molded of gel-coated fiberglass reinforced polyester resin.

Units shall meet or exceed physical and performance requirement for Type 2 gel-coated fixtures [of ANSI Z124.2 showers].

Standing/walking surfaces shall meet slip-resistance requirements of Consumer Safety Specification ASTM F-462, with static friction coefficient no less than 0.04.

Handicapped grab bars shall be nom. 1½" O.D. and support a minimum load of 250lbs. in accordance with the Consumer Safety Specification ASTM F-446 and ANSI A117.1 guidelines.

Units shall have a flame spread rating of 200 or less and a smoke density rating of 450 or less per ASTM E84.

Units shall bear or have a fixed to them a molded manufacturer's logo and/or permanent label showing manufacturer's name and model number and the seal of the Uniform Plumbing Code and shall be accompanied by detailed installation recommendations.

Also affixed and for removal by the owner/occupant/user only, unit shall be equipped with user maintenance instructions and the full text of the limited warranty. As manufactured by Hydro Systems Inc. - Valencia, California.
All specifications subject to change without notice.

 
 ~~ Hydro Systems Whirlpool Baths ~~

NEW!

~~ Hydro Systems Whirlpool Baths ~~

Home | Maestro |Designer | Builder | Shower Pans | Institutional | Options | FAQ | Install | Contacts | Site Map

Hydro Systems Inc.
29132 Avenue Paine, Valencia, CA, 91355 | Tel: 661-775-0686 | Fax: 661-775-0668
sales@hydrosystem.com 
 
© 2004 Hydro Systems. All Rights Reserved